tongue and groove decking 5 4 span

2x6 t&g roof deck - JLC-Online ForumsThere are also several laminated decking products which span longer distances and/or carry heavier loads. For example, made up of 3 plies of 1x6's, with the middle board is offset width wise, so it forms a t&g, in the total thickness. Remember that you need a whole different framing system when you start talking about 4, 5 or 6' deck spans. There are also some issues with this deck as a good roof diaphragm when compared to a std. 5/8" osb deck. You can get about ...【Get Price】

Cumaru Decking Installation - Advantage LumberInstalling tongue and groove on a deck without a roof covering the deck surface will cause problems such as allowing excessive water to collect and cause the material to cup, swell, and buckle. ... Gap Spacing: When installing Cumaru decking, be sure to leave a 1/4" gap between deck boards. This gap spacing may be adequately achieved by selecting the appropriate Ipe Clip<sup> </sup> brand edge mount fastener which completes both functions of fastening and spacing the deck boards at&nbsp;...【Get Price】

Standard for Tongue-and-Groove Roof Decking - American Institute ...Page 5 ... 6.4.4. Standard for tongue-and-groove Roof decking, AITC 112-93 7. 2 ft minimum end joint spacing. Figure 7. Controlled Random Layup. (Two inch decking). Three and Four Inch decking. There shall be a minimum distance of 4 ft ... 4 ft rhinirrhum end joint spacing. Figure 8, Controlled Random Layup. (Three & Four inch decking). Cantilever spans With Controlled Random Layup. When the overhang does not exceed 1-. 1/2 ft, 2 ft and 3 ft for nominal 2 inch, 3 inch, and 4&nbsp;...【Get Price】

Tongue & Groove Decking - SI Storey Lumber CompanyS.I. Storey Lumber Company. tongue and groove. Southern Pine decking. Scope. Southern pine decking is produced by S.I.. Storey Lumber Co., in 2", 3" and 4" thicknesses in accordance with the recommendations of the American Institute ... Three inch decking: * Not less than 40% to be 14' and longer with at least 20% equal to or greater in length than the maximum span as provided by the customer. * Not more than 10% to be less than 10'. * Not more than 1 % to be 4' to 5'.【Get Price】

roof decking roof decking - Boise CascadeThe span tables for the solid sawn decking are shown here. For Alaskan Yellow Cedar in wet-use decking conditions, call Homedale sales for more information. Solid sawn decking serves as a structural load carrying unit and, combined with ... 17/16 x 5. 2.40. 1.000. 2 x 8. 17/16 x 63/4. 2.37. 1.334. *EXAMPLE: 10,000 sq. ft. of roof deck x 2.【Get Price】

Tougue and Groove Roof Decking - American Wood CouncilAMERICAN WOOD COUNCIL. 6. tongue and groove ROOF decking. MINIMUM LENGTHS. If pieces are for controlled random layup, odd or even lengths are permitted, and the minimum lengths based on board feet percentages shall be as follows: Two Inch decking. Not less than 40% to be 14 ft. and longer. Not more than 10% to be less than 10 ft. Not more than 1 % to be 4 to 5 ft. Minimum length is limited to 75% of the span length (i.e., for 8 ft. support spacing, 6 ft.).【Get Price】

Behavior of Plank (Tongue and Groove) Wood Decking under ...The study showed that the established deflection coefficients used to check the deflection of plank decking under balanced uniformly distributed loads can be conservatively used to estimate the stiffness of the simple span, two-span continuous, and controlled random layup patterns. It was also found that a deflection coefficient of 0.60 would be suitable for the combination simple and two-span continuous layup. Under unbalanced loading on two-span continuous layups, it was found&nbsp;...【Get Price】

Tigerwood Deck Installation - Advantage LumberInstalling tongue and groove on a deck without a roof covering the deck surface will cause problems such as allowing excessive water to collect and cause the material to cup, swell, and buckle. ... Gap Spacing: When installing Tigerwood decking, be sure to leave a 1/4" gap between deck boards. This gap spacing may be adequately achieved by selecting the appropriate Ipe Clip<sup> </sup> brand edge mount fastener which completes both functions of fastening and spacing the deck boards at&nbsp;...【Get Price】

The Long and Short of Wood Roof Systems - WoodWorks30 Sep 2014 ... 9/30/2014. 5. Freedom Truck Center, Spokane, WA. Architects: ALSC Architects. Structural Engineer: DCI Engineers. Photo courtesy RedBuilt. Photo Scott Breneman - WoodWorks. University Laval Soccer Stadium, Quebec City ... 9/30/2014. 14. Lumber Roof decking spans. AWC WCD 2 T&G decking Design Tools. Used with Lumber Design Values from National. Design Specification for Wood Construction and. Supplement. Lumber Roof decking spans.【Get Price】

Southern PinePorches without complete roof protection are generally constructed in the same manner as outdoor decks, incorporating a surface of either. 2x6 nominal size or 5/4x6 radius edge pressure-treated Southern Pine. Porch flooring material is widely available and similar in sizes, grades and patterns to flooring used for interior applications. Nominal thicknesses are typically 1 and 1¼ (¾ and 1 actual) with the tongue-and-groove. (T&G) pattern, available in widths of 4 to 6 nominal (3.【Get Price】

Garapa Deck Installation - Advantage LumberInstalling tongue and groove on a deck without a roof covering the deck surface will cause problems such as allowing excessive water to collect and cause the material to cup, swell, and buckle. ... Gap Spacing: When installing Garapa decking, be sure to leave a 1/4" gap between deck boards. This gap spacing may be adequately achieved by selecting the appropriate Ipe Clip<sup> </sup> brand edge mount fastener which completes both functions of fastening and spacing the deck boards at the&nbsp;...【Get Price】

Chapter 23 - International Code CouncilSECTION 2301. GENERAL. 2301.1 Scope. The provisions of this chapter shall govern the materials, design, construction and quality of wood members and their fasteners. 2301.2 General design requirements. The design of struc- tural elements or systems, constructed partially or wholly of wood or wood-based products, shall be in accordance with one of the following methods: 1. Allowable stress design in accordance with Sections. 2304, 2305 and 2306. 2. Load and resistance&nbsp;...【Get Price】

Ipe Deck Install - Advantage LumberIf any building codes or manufacturers installation instructions contradict or differ from information provided by AdvantageLumber.com, contact us for written clarification prior to starting your project. ... Installing tongue and groove on a deck without a roof covering the deck surface will cause problems such as allowing excessive water to collect and cause the material to cup, swell, and buckle. ... decking Dimension, Maximum Joist Spacing. 1x4, 16". 1x6, 16". 5/4x6, 24". 2x6, 32"&nbsp;...【Get Price】